Wire Drawing Machine – Drop By Our Site Next To Track Down Further Advice..

So that you can recycle tires properly, a lot of companies use shredding equipment. However, they can’t use just any ordinary shredder. They need to use one that most closely fits the needs of the company. The two main varieties of Tires Recycling Plants used for this purpose: high-speed and low-speed.


The high-speed shredders are made in the shape of a tub. The scrap from the tires is defined into a container that moves around. Although this is happening, the tires are positioned at the center along with a cutting device shreds or grinds them.

After the process is finished, the outcome is a bunch of rubber that has been shredded. The shredded pieces proceed through an additional round of grinding. These grinders use lots of power. They require it since the grinders need strength to get rid of on the rubber on the tires. Water gets on the tires whenever they reach the hammer mill.

In the hammering process, the rubber is taken away from the steel wire in the beads, belts and sidewalls. Most of the steel wire is removed by magnets. During this time period, more shredding takes place.

A good reason to utilize these tub size grinders is that they give a larger output. It’s estimated they can actually process approximately at least 4,000 tires one hour. If you’re operating the gear, it could most likely be finished with an eight hour time frame, maybe a little bit more.

Rotary Shear

Rotary shear shredders are noted for shredding tires. In this category are the hook-shear shredders as well as the Holman-type shredders.

The hook-shear shredders process the tire scraps on a container. There are blades that are shaped like hooks at the bottom. Because the blades operate, they are separated. During rotation, the tire experiences the blades and get shredded. Hook-shear shredders normally operate at a slow speed.

The Holman shredder can be used for processing scrap tires produced from belted steel. It favors the hook-shear shredder, however the difference will be the rotors are made in a knife shape. Heat shrinking allows the spacers to get connected to the shafts. The spacers cannot tear out of the shafts. The knife is secured for the rotor with bolts. The rotor must be protected by liners to prevent premature damage.

The blades utilized for this type of shredder assistance to cut maintenance costs. The blades also give a fresh cut if the tires get shredded. To bring down costs, this shredder is large on tire feeds. When the entire wheel goes into the shredder, the tire fails to bounce.

Electrical and electronic equipment is a rapidly growing sector within recycling management. Largely right down to the implementation in the WEEE Directive (waste electrical and electronic equipment), the recycling targets of waste electrical items are continually being reviewed.

In 2012, the recast WEEE Directive was published, outlining the new collection targets for waste electrical and electronic equipment. Changes to the UK WEEE system were published on April 17th 2013.

WEEE is a complex waste stream to effectively manage as it is comprised of multiple components and materials. Some of these are valuable recyclable materials like copper and nickel, and some are hazardous nxjycz as arsenic, cadmium, lead and mercury. Because of their mixed composition, it really is imperative that both electrical manufacturers and those that produce waste electrical items employ reliable and effective recycling management for products that fall inside the WEEE regulation

Recycled tires have lots of different uses. It could be shredded for your landfill, or used being a cover. Smaller companies are not the sole ones benefiting from this. Larger operations are emerging and taking over because the dominant force using specialized tire recycling equipment. You should make sure you’re in the right marketplace for it. In addition to the equipment employed for shredding, you need to have manpower, transportation and vehicles to get a successful operation that will give you profits.

Henan Suyuan Lanning Technology Co., Ltd as one of the Chinese leading waste recycling technology research and equipment manufacturing enterprises, Located in zhengzhou,we have business all over 60 countries around the world. We are the famous exporter of scrap wire and cable Recycling production line such as cable stripper machine and cable granulator, Waste motor recycling production lines,Waste Tire/rubber Recycling Equipment?Waste Plastics Recycling Equipment?Waste Radiator Recycling equipment?Waste circuit board recycling equipment?Waste medicine package recycling equipment?copper zipper recycling equipment, copper machine, cans recycling lines,waste refrigerator recycling lines, scrap radiator recycling production lines and other large-scale production lines.

Contact Us:
Address:No.238 South Tongbai Road,Zhongyuan District, Zhengzhou,China
Tel: +86-13525577283
Email: tina@sywasterecycle.com
Tel: +86-13683711610
Email: jack@sywasterecycle.com
Tel: +86-13526863785
Email: julie@sywasterecycle.com

Leave a Reply

Your email address will not be published. Required fields are marked *